Grinding

9 Item(s)

per page

List  Grid 

Set Descending Direction
  1. AcuGrind

    AcuGrind

    • Size Range: 80mm - 250 mm
    • Proofline Sealed
    For OD and ID clamping
    Built-in pneumatic actuation, no hydraulic cylinder required
    Sealed standard chuck for high-precision universal grinding applications
    Highest accuracy - runout and repeatability Learn More
  2. Type D

    Type D

    • Size Range: 8" - 12" (210mm - 315mm)
    • Number of Jaws: 3 Jaws
    • OD or Pitch Line Clamping
    • Centrifugal Force Compensation
    • Proofline Sealed
    Type D diaphragm clamping technology with quick jaw change at its best – for hard turning, grinding, high precision turning. Learn More
  3. D-KOMBI

    D-KOMBI

    • Size Range: 8" - 12" (210mm - 315mm)
    • Number of Jaws: 3 Jaws
    • Radial and Axial Clamping
    • Flat Gripping Force Curve
    • Proofline Sealed
    D-KOMBI Quick Jaw Change Diaphragm Chucks are ideal for clamping of thin walled workpieces in hard turning and grinding applications. The operation is based on the elastic deformation of the diaphragm, so there are no sliding parts and no friction. Learn More
  4. D-PLUS

    D-PLUS

    • Size Range: 260mm-315mm
    • Number of Jaws: 3 jaws
    • Through Hole: 32mm - 50mm
    • Centrifugal Force Compensation
    • OD or Pitch Line Clamping
    The first and only open center diaphragm chuck in the industry. Giving super high-precision turning, grinding or milling operations a superior final finish, the D-Plus Diaphragm chuck is ideal for shaft type work pieces, such as input and output shafts, where sub-micron accuracy is mandatory. Learn More
  5. Type D-VARIO

    Type D-VARIO

    • Size Range: 8" (215mm)
    • Fine adjustment of the center line
    • Key Lock System = Quick positioning of jaws for gears with different number of teeth
    • Jaws for pitch line or outside clamping
    • Proofline Sealed
    Type D-VARIO offers a Flexible solution for grinding with quick adjustment for short set up times. Learn More
  6. EM-S

    EM-S

    • Size Range: 18mm - 105mm
    • For turning grinding and milling
    • Large expansibility
    • Very Rigid Design
    • Case hardened / wear resistant
    EM-S are power operated segment sleeve mandrels that are deal for volume production and hard turning / grinding with wear resistant, case hardened and vulcanised clamping sleeves. Axial pull down by the axial clamping movement of the clamping sleeve = best face run out. Learn More
  7. SRG / SRG-B

    SRG / SRG-B

    • Clamp Range: 3mm - 136mm
    The SRG is a grinding series steady rest designed to support shaft type workpieces on grinding machines. It is well suited for the machining of crankshafts and camshafts. The SRG allows for rapid alignment of the steady rest/work piece to the centerline with fine adjustment dials. It is follow down capable for applications with varying diameters.
    Learn More
  8. FDG

    FDG

    • Machining of the entire surface of the workpiece with one single operation
    • Power operated on the side of the spindle
    • Highest run-out accuracy
    • Center pin with carbide insert

    Face drivers for grinding between center pins. Machine the entire surface of the workpiece in one single operation


    Learn More
  9. CPG

    CPG

    • For Diaphragm Chuck D-VARIO and Face Driver FDG
    Easy installation for grinding and turning machines without hydraulic unit.
    Learn More

9 Item(s)

per page

List  Grid 

Set Descending Direction